Re: Creo 2.0 RESTARTING my computer once I open a file!
Welcome to the forum, Jared. Creo is very dependent on the graphics driver and as such, it could well be that activating the second screen may have changed something. However, rebooting is not one of...
View ArticleRe: Creo 2.0 RESTARTING my computer once I open a file!
Thank You, *** "You could try changing the driver setting to "graphics win32_gdi" in config,.pro to see if this helps." *** How would I go about doing this? - Jared Sand
View ArticleRe: Creo 2.0 RESTARTING my computer once I open a file!
It depends on how your system is currently reading the configuration file.If you created a config.pro file and it resides in a custom location, you can edit this file with a text editor. You would add...
View ArticleRe: I want to combine different 2 vecctors
Unfortunately, I'm Mathcadless at the moment, but if you look in the worksheet I've attached to this message http://communities.ptc.com/message/266834#266834 I hope you will find the functions set...
View ArticleRe: How to save file
if one has mac and other windows...so that means they are different ..so they will have separate name..they can only have the same name when they are 100% similar....and then the one will be called a...
View ArticleRe: I want to combine different 2 vecctors
Thank you. I settle finally to use "submatrix" so you don't need to think about my question anymore.Thank you for consideration.
View ArticleRe: Can an optimization analysis take LDA´s "user defined output steps"...
Thanks for your feedback. In some cases yes. The optimization needs to act at a determined step. In some non-linear mechanical system some parameters (ex. resulting force, tilts, stress, etc.) will...
View ArticleRe: Is export graph to Excel limited to 100 points in Creo Simulate?
No, there was no warning that the 100 first points are the limit. I found this issue only after exporting a transient analysis graph. Creo 2 Thermal was exporting only the 1st 100 points independently...
View ArticleRe: How to save file
There'd be no two different design softwares if there'd be no two different people both needing a design software. Yes, Creo is different and at many functionalities archaic, but as Antonius has...
View ArticleRe: transfer Creo orthographic drawing into Word document
Hi Burhan, From within Word, try Insert → Object → PTC Drawing Document then find & select the .drw file and it should insert it into the drawing. I've not used this very much, so I don't know how...
View ArticleRe: transfer Creo orthographic drawing into Word document
Thank you so much. really appreciate your suggestion.
View ArticleRe: transfer Creo orthographic drawing into Word document
Thank you so much. really appreciate your suggestion.
View ArticleRe: transfer Creo orthographic drawing into Word document
Thank you so much. really appreciate your suggestion.
View ArticleRe: transfer Creo orthographic drawing into Word document
Thank you so much. really appreciate your suggestion.
View ArticleClik here to view.
Re: transfer Creo orthographic drawing into Word document
All the suggestions are helpful and I am very appreciate them.
View ArticleAssembly constraints
I have been assembling a large amount of parts and subassemblies lately and thought it was time to ask this question:Is there a config option I can set that I can have:1. Coincident set...
View ArticleWindchill generate bad url for the object info page
Hi. I've created the mvc component (table, that display a list of the WTDocuments). This component is placed inside the navigator page. The first field is the number and this field is the link to the...
View ArticleWhen implementing a new constraint, what moves into production?
Hello,I have created a table in production with a primary key constraint.I want to add a foreign key constraint.I use a source member that gets moved and then RUNSQLSTM with a special command that adds...
View Article