Re: Creo3 fasteners & 'carries shear'
Agreed, springs aren't the same. Mind you, everything is an approximation and in my case, carrying shear is not good. I thought the change over was with the intro of Creo1.0
View ArticleRe: PTC Creo 3.0 Now Available!
Chris,I found the More tab in sketcher thanks. Why was a new tab created rather than moving them into the sketcher drop-down? I restored the ui file to the text folder but the Schools tab doesn't...
View ArticleRe: Which 3 button mouse do you recommend?
I ended up with the 4 wired. After using it for a few days I replaced my keyboard with a mini keyboard. I found with the Evoluent my right hand needed to travel too far. Wish I could have afforded a...
View ArticleRe: Creo 2.0 Student-Version doesn´t open
Ok, everytime the window opens this warning appears: Warning: Proper TCP/IP configuration was not detected The TCP/IP protocol is not installed or configured properly.
View ArticleRe: Given/Find "this variable is undefined"
hey guys thanks a million. you both are right. gotta admit im kinda new using mathcad to solve themodynamics problems, i usually use a couple of special excelsheets to solve them, but in this case...
View ArticleRe: Given/Find "this variable is undefined"
You have assigned the results of the solve block to the vector "solucion" and not to the variables used for the calculation. So they still are assigned the guess values.You either have to assign a...
View ArticleClik here to view.
Re: Given/Find "this variable is undefined"
There are at least two problems in your sheet. The most prominent one is a simple typo you can quickly find using "Trace error" as Alan had shown:The system still will not solve after you delete that...
View ArticleRe: Creo 3.0 - Licence request failed for feature
I am trying to install creo3.0 and I am having the same problem as mr. cramlet. I used the code BK400407EDSTUDENTUNICL for the simple license error. I don't understand what exactly mr. cramlet did to...
View ArticleRe: Optimizing (max / min) of a function in terms of parameters given:
Part of issue with 15 is the graph displays. It is very slow when I scroll, especially if I have multiple lines on the same graph. Might be some setting I can alter to change that I am unaware of or...
View ArticleRe: Optimizing (max / min) of a function in terms of parameters given:
Part of issue with 15 is the graph displays. It is very slow when I scroll, especially if I have multiple lines on the same graph.I guess this is only the case when you open the sheet the first time or...
View ArticleRe: Optimizing (max / min) of a function in terms of parameters given:
Correction:Generally it would be hard impossible to believe that MC15 is slower than Prime.
View ArticleClik here to view.
Re: is it possible to track "b-graph" on "a-graph"
I mean a_graph is changed to b_graph.I have airfoil data each. I need to consider mutation becasue airfoil is changed.I just have cross-sectional area data. so I consider variation area.I attached...
View ArticleRe: Optimizing (max / min) of a function in terms of parameters given:
Actually, the problem only really appears when I have the zoom at say 200% or 150% and have scrolled to the bottom, and then start scrolling up, it acts like it is replotting the graphs for each...
View ArticleRe: Optimizing (max / min) of a function in terms of parameters given:
Richard Jackson wrote: Correction:Generally it would be hard impossible to believe that MC15 is slower than Prime.Sorry, my fault. You are perfectly right. :-)
View ArticleRe: Optimizing (max / min) of a function in terms of parameters given:
Jake Roth wrote: Actually, the problem only really appears when I have the zoom at say 200% or 150% and have scrolled to the bottom, and then start scrolling up, it acts like it is replotting the...
View ArticleLicense Request Failed for Feature
This is the error I get when I try to load Creo Parametric 3.0 on a 64-bit Windows computer. This is the school version.
View ArticleDynamic Bellow Design
I am certainly impressed with the dynamic aspect in this definition of a bellows design. It is a single sketch capable of significant number of cells while remaining dynamic. The OD and ID convolution...
View ArticleRe: License Request Failed for Feature
http://www.ptc.com/communities/academic-program/technical-support
View ArticleRe: Create a centre line in a drawing on a swept profile
I'd select the surface generated by the radius and add an axis. Creo doesn't do it because it can't be sure the extrusion will be linear when using a sweep. Since an axis can't bend around a curved...
View Article