Re: Create solid models from .dwg files.
how to get .dwg in sketcher???it shows me error :O
View ArticleRe: Create solid models from .dwg files.
This is not unusual. Sketcher is trying to apply the solver to the import. If the sketch is too complicated it will throw out an error which you normally continue from. If you need a complex sketch...
View ArticleRe: Create solid models from .dwg files.
>>file>>open>>select the .dwg file you want to open>>on "import new model", select part and use automatic templates>>click okay and the file opens as an editable...
View ArticleRe: Not Responding
I have been on Pro|E for a long time and now I am on Creo. My old Windows NT workstation use to simply quit and do a cold-crash of Pro|E. It had the simple approved FireGL graphics card and enough...
View ArticleRe: Create solid models from .dwg files.
Great video, Damian. What are you using for capture software?
View Articleedit patterns in an assembly
Does anyone know how to edit a hole pattern in an assembly? I screwed up in the placement of the holes and cannot get back into the pattern to correct it. The end goal is to use screws/bolts to hold...
View ArticleRe: Create solid models from .dwg files.
Creo has a tool autobuildZ to create 3D models from 2D drawings. Information in the help files and the knowledge base (videos).You enable it by autobuildz_enabled yes in your config.proReinhard
View ArticleRe: Need closed polylines when exporting drw to dwg...
I just went through this. They should accept arcs, lines, ellipses... etc... but splines need to be converted to polylines. The default it spline. Use the File>Export dialog and select DXF....
View ArticleRe: I'm trying to create a continuous function with some added delta's.
I think the better solution is in the last post (that with the two "return"s http://communities.ptc.com/message/209610#209610). I don't think that using Kroneckers Delta or the boolean comparison is...
View ArticleRe: Creo 2.0 (M010) - Cannot Dimension Sketch in Drawing
Hello, if you need a dimmension of theo "sharp edge" than try following: In model:1. sketch an extrude with sharp edges (make dimmensions else you wish) --- complete an extrude2. make a round feater...
View ArticleRe: I'm trying to create a continuous function with some added delta's.
Jay Smith wrote: Werner, Wow, thank-you very much for your informative reply. I appreciate your time, efforts and suggestions. Sorry for leaving that log 0 reference, I certainly know better You...
View ArticleRe: Need closed polylines when exporting drw to dwg...
Hi, This is propably just another accuracy problem. Make sure the accuracy of the model is set to absolute 0.001 (mm) at least. Even imported model data should export to *.dwg drawing file just fine....
View ArticleRe: hi
If you don't have Save-As as shown here, then you must have the Educational version of Creo. I believe that version will not let you save as other file types.
View ArticleRe: Creo 2.0 (M010) - Cannot Dimension Sketch in Drawing
Vojtech, Thanks for the reply. The only problem is that these dimensions do not exist in my case. I didn't think to mention my complete workflow to get to this point. This is a tool to create a part...
View ArticleV10 Exporting Lifecycle Error
trying to export a lifecycle template from windchill v10...but getting the following error (wt.lifecycle.lifecycleResource/224) wt.util.WTException: Do not support export on a disabled life cycle...
View ArticleRe: ActiveX implementation of Editor
Hi Peter-- I've done this in a few installations. However, you may be disappointed if you are looking at this as a "zero footprint" solution. Using Arbortext Editor as an ActiveX control in a web page...
View ArticleRe: Developing code in Workflow Template Administrator
I didn't follow it that closely, but I have a couple thoughts. Checking QueryResult == null doesn't hurt and is certainly cautious, I just can't think of any instance that will return a null...
View ArticleRe: Too frequent corruption of optimization analyses AND model!
Right, these names should not be a problem. I can't run A130717_1856_OPT2 because some of the shells are not part of the 2D model definition. Made a number of edits to resolve this, but didn't...
View Article