Quantcast
Channel: PTC Community: Message List
Browsing all 12488 articles
Browse latest View live

Re: how to punch this in proe/creo sheetmetal?

Is that the workpiece of the form?

View Article


Re: Creo 2.0 M120 - Any feedback on this version anyone?

I had M120 installed a couple of days ago and haven't noticed any issues. I got it to test if for large assembly drawing performance improvements. I haven't done any real testing though. Just normal use.

View Article


Image may be NSFW.
Clik here to view.

Re: Table of results

JOHN WOODGATE wrote: This, too, is not too difficult for me, but maybe more than I require. I'm using Mathcad 15 at present. Thank you very much.  How can I retrieve your worksheet/ I can screen-grab,...

View Article

Re: Table of results

JOHN WOODGATE wrote: Thank you. I don't understand your reference to 'live data'. Do you mean that I shoudl have uploaded my Mathcad worksheet?Exactly that! Either your original sheet, or, if it...

View Article

Re: Windchill installation problem can't join Std out or Std err

Gary Mansell wrote: I think that when the PSI is re-run on a failed install, that when it is run again, it reads some properties from the previously created in the loadpoint's site.xconf file. This is...

View Article


Re: Windchill installation problem can't join Std out or Std err

OK - it must only be when you update an existing installation rather than an install that it reads from the site.xconf files then. In that case, just check the properties in the psi_ii.xml file as...

View Article

Re: Windchill installation problem can't join Std out or Std err

Gary Mansell wrote: On a similar vein - check the C:\ptc\PSI\installer\instreg\ii389c79d6.13f37e76814.-8000\psi_iir.xml file for this value: <Variable...

View Article

Re: Drawing View Cross Sections

I was thinking about it and I use it for tons of breakouts for showing hardware on assembly drawings. It's been available for as long as I have been using pro/e (version 15 around 1995). It's an...

View Article


Re: Windchill installation problem can't join Std out or Std err

You are sure that there is no https configuration involved here - is that correct? I can't see it can be if you are doing a fresh install, but thought I should check... The reason I mention this is...

View Article


Image may be NSFW.
Clik here to view.

Re: Windchill installation problem can't join Std out or Std err

The main reason I included the SSL port was because I was prompted for during the install. No other reason really....   In any event, thanks for your time and effort....  I may just have to re-run it...

View Article

Re: Creo Parametric 3.0 - Notes Normal to Screen

Nice catch, Yong.

View Article

Re: Drawing View Cross Sections

Now I know you can do it and you have pointed out how it can be used, I have already found an application!It just goes to prove that you are never too old to learn new things. Of course, it may be that...

View Article

Re: Creo Parametric 3.0 - Notes Normal to Screen

The problem is the leader line is removed after I make the note flat to the screen.  Setting the config.pro option did not correct this.

View Article


Re: Creo Parametric 3.0 - Notes Normal to Screen

Read the first line (question) in my problem statement.

View Article

Re: Manual pro-e data migration from Intralink 9 to windchill pdmlink 10.2

Some commercial reasons behind that Any ansers or advice for me for just to complete 5000 parts delta now

View Article


Re: Surfacing Help, 5 Sided Surface and Continuity

Not sure it will help but this blog seems to me to be a good resource for surfacing in Pro/E. http://learn.lboro.ac.uk/ludata/cd/cad/mod_level2/surfacing1.htm(Loughborough Design School.  © Sean...

View Article

PTC creo parametrics elearning promo codes ?

Hi, I am going to buy creo parametrics elearning courses, I saw the promo code box on the proceed to checkout page, so where can I find one for buy the product at some discount, because I am poor, the...

View Article


Re: error in opening PTC cero files in proe 4.0

Creo files are not backward compatible.  There is a tool called Granite that will help you.  It is easiest to import a STEP file if you can get the original file converted....

View Article

Re: PTC creo parametrics elearning promo codes ?

Contact your local reseller and ask about academic discounts.

View Article

Image may be NSFW.
Clik here to view.

Re: Surfacing Help, 5 Sided Surface and Continuity

No problem about 5-side surface in style feature. Trouble with boundary blend but there are some tricks. See if my solution can be good. If you need i can give you a solution without style features...

View Article
Browsing all 12488 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>