Re: Extract data from chart
I personally don't use the sheet at all. I posted it because you asked for a solution in Mathcad. I have a piece of software called Un-Scan-It, which does a much better job. And yes, I sometimes clean...
View ArticleClik here to view.
Re: Cannot understand this syntax.
Hello, again. Is there a way to prove ( with Symbolics and Manual ) the following ? : Thanks in advance for your time and help. Regards.
View Article.mtl library in windchill
I have a problem and I hope enyone could help me with that. How can I create a .mtl library at the First Windchill server? I save the .mtl-file in my workspace but i couldn't check it in. Also the...
View ArticleRe: sketcher dimension the way we want...
Good. Now they can get cracking on the curvture element and dimension so you can go from +radius, to straight, to -radius with the same curve element.
View ArticleRe: Integrity Gateway advanced parser documentation
Hello Marc, Actually, I missed this earlier, but it might be helpful: Please see page 76 of the Integrity 10.5 Gateway User Guide. There is brief discussion given on the table under DSD/XSLT...
View ArticleClik here to view.
Is there any method or plugin could translate the expression between Mathcad...
During using Mathcad, sometime I need some functions that mathcad don't have, such as plot a complicated function or put it in a Geometry Software like Geogbra, then I must translate the mathcad...
View ArticleRe: Creo mankin user guide
Hi Sagar, The following link might be helpful.https://www.ptc.com/appserver/cs/view/solution.jsp?n=CS171444&source=tssearch
View ArticleFetching complete list of fields/attributes/properties for types
Hi, we're facing a problem while fetching all fields/attributes/properties available for an issue type via CLI. in general we try to provide some kind of content assist to support users while...
View ArticleRe: Exporting a cross section of geometry in Excel / measure thickness of...
It the density of the points is sufficient in the line definition, yes, this is a good way. I you need more points, you can place a point along a curve (datum point, select a curve or edge, set a...
View ArticleRe: Just Loaded Creo3.0
Are you running other versions on a fixed license? Just gathering loading options.
View ArticleRe: ever tried in Flexmove tool..in pro/e?
So if I want this option, I have to load WF5?
View ArticleRe: Creo 3.0 Unite Technology Import Capability
Hey Steven, I installed this version also and did not have the same positive results. Tried importing about 3 different file types. I tried the SLDPRT and SLDASM with no luck. Locked up my system. Also...
View ArticleClik here to view.
K Factor Grayed Out
Hello Everyone. Here's a question about the K Factor in a component. When I open a part, I go to the EDIT menu and select SETUP, from there I'm able to select the bend allowance and select my K/Y...
View ArticleRe: Odesolve failure - Kenneth Macfarlane
Alan I've realised that the Odesolve_Test file I sent on 18 July had a different spring stiffness from the results I added on 21 July. I reconciled this on the attached updated version of...
View Articlesum several sin
Hi All, I have a problem. Here I discribe the case. A triplex plunger pump will produce water hammer. This will create a sinus wave, by opening the inletvalve and closing the inletvalve. I have 3...
View ArticleClik here to view.
Re: About making draft lines
I have created 3 versions using the sweep technique. Each more preferable then the previous depending on the level of effort required. 1st is a simple sweep that follows the exiting edges of the...
View ArticleRe: Challenged with Pro Mold
There are a lot of tools that come with it, and I hate saying it this way, but they just don't work or they only work in the rare times you design to a really really simple part. They need to offer a...
View ArticleClik here to view.
Re: Probable error in function evaluation
Floyd, are you running the version manager extension?
View Article